PendoTECH / Products / Sensors and Monitors / Conductivity Sensor & Transmitters

Conductivity Sensors & Transmitters

PendoTECH’s Single-Use Conductivity Sensors and Conductivity Transmitter offer highly accurate conductivity and temperature measurements without requiring sensor calibration. Each sensor comes with a pre-determined cell constant, which is entered into the transmitter. Ideal for use in critical bioprocess operations, the sensor transmitter connects to the PendoTECH Single-Use Conductivity Sensor and produces a linear 4-20 milliamp signal with conductivity. It reads the sensor’s raw conductivity and temperature value and calculates the normalized value at 25°C. The normalized value is transmitted via the 4-20 mA signal in the 0-150 mS range. It has a convenient DIN rail mounting design.


Sensor Specifications:

  • Range: 0.1 to 100mS/cm
  • Accuracy from:
    • 0.1 to 2 mS/cm ± 0.1mS/cm;
    • 2 to 50 mS/cm ± 5% of reading;
    • 50 to 100 mS/cm typically ± 5% of reading
  • Pressure Rating: 75psi (5bar)
  • Fluid Path Materials:
    • Gamma compatible (up to 50kiloGrays)
    • NaOH resistant
    • USP Class VI
  • Temperature measurement for normalization by monitor
  • No calibration required because of pre-determined cell constant; in the range from 0 to 70°C and one-point calibration by user optional
  • Designed for single use applications; may be repeatedly cleaned and re-used

Transmitter Details:

  • Reads conductivity and temperature from sensor
  • Reads 2 sensors; including ability to read temperature only
  • Cell constant must be entered into the monitor when new sensor is connected
  • Perform temperature normalization to 25°C with adjustable mS/ °C factor
  • 4 – 20mA outputs for both conductivity and temperature
  • RS232 output for data collection to a PC with PendoTECH PMAT Plus GUI software
  • Panel mount kit and benchtop stand available
Model/Part Number CT2
4-Wire
Number of Sensor Channels 1 conductivity channel
Number of Flow Channels –
Communication –
Panel Cutout request drawing
Analog input –
Digital input –
Relays / open collectors (OC) –
Outputs (1) 4-20mA
Approvals CE Mark EN61326-1:2013; EN 50581:2012; REACH and RoHS Complaint
Parameter compatibility
PendoTECH conductivity, 2E, single-use sensor yes

Software

  • PMATP-GUI: Data Acquisition and Trending Software for PressureMAT and CMONT with 2 USB/serial cables to connect to a PC

Stands

  • PMAT-STND: Bench top stand for PressureMAT

Water Tight Enclosures

  • PMAT-BNCH-COMBO: PressureMAT, CMONT with UV Optional water-tight bench top stainless steel box with water-tight cable connections on left side

Cables

  • CMONT-650-298: Cable adaptor with D15 male for Single Use Conductivity Sensor for CMONT (10ft/3.04M)

Accessories

  • CMONT-TKS: PendoTECH Conductivity Monitor test kit for conductance and temperature verification
  • CMONT-PWR: 24 Volt power supplies for CMONT
  • CMONT-PANEL: CMONT Panel Mount Upgrade Kit- 2 gaskets (one and a spare), 4 mounting brackets, 4 screws, 2 sensor cables (CN-650-298), 2 connectors (one for each input), and power input connector
  • CMONT-DIN: DIN rail mounting kit for CMONT
  • PDKT-650-298BH: Pressure Sensor Bulkhead Connector with 6 inch Flying Leads

Additional Products

PendoTECH Publication
Back to Top